/**
******************************************************************************
* @file stm32f0xx.h
* @author MCD Application Team
* @version V1.5.0
* @date 05-December-2014
* @brief CMSIS Cortex-M0 Device Peripheral Access Layer Header File.
* This file contains all the peripheral register's definitions, bits
* definitions and memory mapping for STM32F0xx devices.
*
* The file is the unique include file that the application programmer
* is using in the C source code, usually in main.c. This file contains:
* - Configuration section that allows to select:
* - The device used in the target application
* - To use or not the peripheral’s drivers in application code(i.e.
* code will be based on direct access to peripheral’s registers
* rather than drivers API), this option is controlled by
* "#define USE_STDPERIPH_DRIVER"
* - To change few application-specific parameters such as the HSE
* crystal frequency
* - Data structures and the address mapping for all peripherals
* - Peripheral's registers declarations and bits definition
* - Macros to access peripheral’s registers hardware
*
******************************************************************************
* @attention
*
*
© COPYRIGHT 2014 STMicroelectronics
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/** @addtogroup CMSIS
* @{
*/
/** @addtogroup stm32f0xx
* @{
*/
#ifndef __STM32F0XX_H
#define __STM32F0XX_H
#ifdef __cplusplus
extern "C" {
#endif
/** @addtogroup Library_configuration_section
* @{
*/
/* Uncomment the line below according to the target STM32F0 device used in your
application
*/
#if !defined (STM32F030) && !defined (STM32F031) && !defined (STM32F051) && \
!defined (STM32F072) && !defined (STM32F042) && !defined (STM32F091) && \
!defined (STM32F070xB) && !defined (STM32F070x6) && !defined (STM32F030xC)
/* #define STM32F030 */
/* #define STM32F031 */
/* #define STM32F051 */
/* #define STM32F072 */
/* #define STM32F070xB */
/* #define STM32F042 */
/* #define STM32F070x6 */
/* #define STM32F091 */
/* #define STM32F030xC */
#endif /* STM32F030 || STM32F031 || STM32F051 || STM32F072 || STM32F042 || STM32F091 ||
STM32F070xB || STM32F070x6 || STM32F030xC */
/* Tip: To avoid modifying this file each time you need to switch between these
devices, you can define the device in your toolchain compiler preprocessor.
*/
/* Old STM32F0XX definition, maintained for legacy purpose */
#if defined(STM32F0XX) || defined(STM32F0XX_MD)
#define STM32F051
#endif /* STM32F0XX */
/* Old STM32F0XX_LD definition, maintained for legacy purpose */
#ifdef STM32F0XX_LD
#define STM32F031
#endif /* STM32F0XX_LD */
/* Old STM32F0XX_HD definition, maintained for legacy purpose */
#ifdef STM32F0XX_HD
#define STM32F072
#endif /* STM32F0XX_HD */
/* Old STM32F030X6/X8 definition, maintained for legacy purpose */
#if defined (STM32F030X8) || defined (STM32F030X6)
#define STM32F030
#endif /* STM32F030X8 or STM32F030X6 */
#if !defined (STM32F030) && !defined (STM32F031) && !defined (STM32F051) && \
!defined (STM32F072) && !defined (STM32F042) && !defined (STM32F091) && \
!defined (STM32F070xB) && !defined (STM32F070x6) && !defined (STM32F030xC)
#error "Please select first the target STM32F0xx device used in your application (in stm32f0xx.h file)"
#endif /* STM32F030 || STM32F031 || STM32F051 || STM32F072 || STM32F042 || STM32F091 ||
STM32F070xB || STM32F070x6 || STM32F030xC */
#if !defined USE_STDPERIPH_DRIVER
/**
* @brief Comment the line below if you will not use the peripherals drivers.
In this case, these drivers will not be included and the application code will
be based on direct access to peripherals registers
*/
/*#define USE_STDPERIPH_DRIVER*/
#endif /* USE_STDPERIPH_DRIVER */
/**
* @brief In the following line adjust the value of External High Speed oscillator (HSE)
used in your application
Tip: To avoid modifying this file each time you need to use different HSE, you
can define the HSE value in your toolchain compiler preprocessor.
*/
#if !defined (HSE_VALUE)
#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz*/
#endif /* HSE_VALUE */
/**
* @brief In the following line adjust the External High Speed oscillator (HSE) Startup
Timeout value
*/
#if !defined (HSE_STARTUP_TIMEOUT)
#define HSE_STARTUP_TIMEOUT ((uint16_t)0x5000) /*!< Time out for HSE start up */
#endif /* HSE_STARTUP_TIMEOUT */
/**
* @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
Timeout value
*/
#if !defined (HSI_STARTUP_TIMEOUT)
#define HSI_STARTUP_TIMEOUT ((uint16_t)0x5000) /*!< Time out for HSI start up */
#endif /* HSI_STARTUP_TIMEOUT */
#if !defined (HSI_VALUE)
#define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal High Speed oscillator in Hz.
The real value may vary depending on the variations
in voltage and temperature. */
#endif /* HSI_VALUE */
#if !defined (HSI14_VALUE)
#define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz.
The real value may vary depending on the variations
in voltage and temperature. */
#endif /* HSI14_VALUE */
#if !defined (HSI48_VALUE)
#define HSI48_VALUE ((uint32_t)48000000) /*!< Value of the Internal High Speed oscillator for USB in Hz.
The real value may vary depending on the variations
in voltage and temperature. */
#endif /* HSI48_VALUE */
#if !defined (LSI_VALUE)
#define LSI_VALUE ((uint32_t)40000) /*!< Value of the Internal Low Speed oscillator in Hz
The real value may vary depending on the variations
in voltage and temperature. */
#endif /* LSI_VALUE */
#if !defined (LSE_VALUE)
#define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
#endif /* LSE_VALUE */
/**
* @brief STM32F0xx Standard Peripheral Library version number V1.4.0
*/
#define __STM32F0XX_STDPERIPH_VERSION_MAIN (0x01) /*!< [31:24] main version */
#define __STM32F0XX_STDPERIPH_VERSION_SUB1 (0x05) /*!< [23:16] sub1 version */
#define __STM32F0XX_STDPERIPH_VERSION_SUB2 (0x00) /*!< [15:8] sub2 version */
#define __STM32F0XX_STDPERIPH_VERSION_RC (0x00) /*!< [7:0] release candidate */
#define __STM32F0XX_STDPERIPH_VERSION ((__STM32F0XX_STDPERIPH_VERSION_MAIN << 24)\
|(__STM32F0XX_STDPERIPH_VERSION_SUB1 << 16)\
|(__STM32F0XX_STDPERIPH_VERSION_SUB2 << 8)\
|(__STM32F0XX_STDPERIPH_VERSION_RC))
/**
* @}
*/
/** @addtogroup Configuration_section_for_CMSIS
* @{
*/
/**
* @brief STM32F0xx Interrupt Number Definition, according to the selected device
* in @ref Library_configuration_section
*/
#define __CM0_REV 0 /*!< Core Revision r0p0 */
#define __MPU_PRESENT 0 /*!< STM32F0xx do not provide MPU */
#define __NVIC_PRIO_BITS 2 /*!< STM32F0xx uses 2 Bits for the Priority Levels */
#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */
/*!< Interrupt Number Definition */
typedef enum IRQn
{
/****** Cortex-M0 Processor Exceptions Numbers ******************************************************/
NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */
HardFault_IRQn = -13, /*!< 3 Cortex-M0 Hard Fault Interrupt */
SVC_IRQn = -5, /*!< 11 Cortex-M0 SV Call Interrupt */
PendSV_IRQn = -2, /*!< 14 Cortex-M0 Pend SV Interrupt */
SysTick_IRQn = -1, /*!< 15 Cortex-M0 System Tick Interrupt */
#if defined (STM32F051)
/****** STM32F051 specific Interrupt Numbers *************************************/
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
PVD_IRQn = 1, /*!< PVD through EXTI Line detect Interrupt */
RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */
FLASH_IRQn = 3, /*!< FLASH Interrupt */
RCC_IRQn = 4, /*!< RCC Interrupt */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
TS_IRQn = 8, /*!< Touch sense controller Interrupt */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */
ADC1_COMP_IRQn = 12, /*!< ADC1, COMP1 and COMP2 Interrupts */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM2_IRQn = 15, /*!< TIM2 Interrupt */
TIM3_IRQn = 16, /*!< TIM3 Interrupt */
TIM6_DAC_IRQn = 17, /*!< TIM6 and DAC Interrupts */
TIM14_IRQn = 19, /*!< TIM14 Interrupt */
TIM15_IRQn = 20, /*!< TIM15 Interrupt */
TIM16_IRQn = 21, /*!< TIM16 Interrupt */
TIM17_IRQn = 22, /*!< TIM17 Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Interrupt */
I2C2_IRQn = 24, /*!< I2C2 Interrupt */
SPI1_IRQn = 25, /*!< SPI1 Interrupt */
SPI2_IRQn = 26, /*!< SPI2 Interrupt */
USART1_IRQn = 27, /*!< USART1 Interrupt */
USART2_IRQn = 28, /*!< USART2 Interrupt */
CEC_IRQn = 30 /*!< CEC Interrupt */
#elif defined (STM32F031)
/****** STM32F031 specific Interrupt Numbers *************************************/
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
PVD_IRQn = 1, /*!< PVD through EXTI Line detect Interrupt */
RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */
FLASH_IRQn = 3, /*!< FLASH Interrupt */
RCC_IRQn = 4, /*!< RCC Interrupt */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */
ADC1_IRQn = 12, /*!< ADC1 Interrupt */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM2_IRQn = 15, /*!< TIM2 Interrupt */
TIM3_IRQn = 16, /*!< TIM3 Interrupt */
TIM14_IRQn = 19, /*!< TIM14 Interrupt */
TIM16_IRQn = 21, /*!< TIM16 Interrupt */
TIM17_IRQn = 22, /*!< TIM17 Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Interrupt */
SPI1_IRQn = 25, /*!< SPI1 Interrupt */
USART1_IRQn = 27 /*!< USART1 Interrupt */
#elif defined (STM32F030)
/****** STM32F030 specific Interrupt Numbers *************************************/
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */
FLASH_IRQn = 3, /*!< FLASH Interrupt */
RCC_IRQn = 4, /*!< RCC Interrupt */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */
ADC1_IRQn = 12, /*!< ADC1 Interrupt */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM3_IRQn = 16, /*!< TIM3 Interrupt */
TIM14_IRQn = 19, /*!< TIM14 Interrupt */
TIM15_IRQn = 20, /*!< TIM15 Interrupt */
TIM16_IRQn = 21, /*!< TIM16 Interrupt */
TIM17_IRQn = 22, /*!< TIM17 Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Interrupt */
I2C2_IRQn = 24, /*!< I2C2 Interrupt */
SPI1_IRQn = 25, /*!< SPI1 Interrupt */
SPI2_IRQn = 26, /*!< SPI2 Interrupt */
USART1_IRQn = 27, /*!< USART1 Interrupt */
USART2_IRQn = 28 /*!< USART2 Interrupt */
#elif defined (STM32F072)
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
PVD_VDDIO2_IRQn = 1, /*!< PVD and VDDIO2 supply comparator through EXTI Line detect Interrupt */
RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */
FLASH_IRQn = 3, /*!< FLASH Interrupt */
RCC_CRS_IRQn = 4, /*!< RCC and CRS Interrupts */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
TSC_IRQn = 8, /*!< TSC Interrupt */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_6_7_IRQn = 11, /*!< DMA1 Channel 4, Channel 5, Channel 6 and Channel 7 Interrupts */
ADC1_COMP_IRQn = 12, /*!< ADC1, COMP1 and COMP2 Interrupts */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM2_IRQn = 15, /*!< TIM2 Interrupt */
TIM3_IRQn = 16, /*!< TIM3 Interrupt */
TIM6_DAC_IRQn = 17, /*!< TIM6 and DAC Interrupts */
TIM7_IRQn = 18, /*!< TIM7 Interrupts */
TIM14_IRQn = 19, /*!< TIM14 Interrupt */
TIM15_IRQn = 20, /*!< TIM15 Interrupt */
TIM16_IRQn = 21, /*!< TIM16 Interrupt */
TIM17_IRQn = 22, /*!< TIM17 Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Interrupt */
I2C2_IRQn = 24, /*!< I2C2 Interrupt */
SPI1_IRQn = 25, /*!< SPI1 Interrupt */
SPI2_IRQn = 26, /*!< SPI2 Interrupt */
USART1_IRQn = 27, /*!< USART1 Interrupt */
USART2_IRQn = 28, /*!< USART2 Interrupt */
USART3_4_IRQn = 29, /*!< USART3 and USART4 Interrupts */
CEC_CAN_IRQn = 30, /*!< CEC and CAN Interrupts */
USB_IRQn = 31 /*!< USB Low Priority global Interrupt */
#elif defined (STM32F042)
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
PVD_VDDIO2_IRQn = 1, /*!< PVD and VDDIO2 supply comparator through EXTI Line detect Interrupt */
RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */
FLASH_IRQn = 3, /*!< FLASH Interrupt */
RCC_CRS_IRQn = 4, /*!< RCC and CRS Interrupts */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
TSC_IRQn = 8, /*!< TSC Interrupt */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4, Channel 5 Interrupts */
ADC1_IRQn = 12, /*!< ADC1 Interrupts */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM2_IRQn = 15, /*!< TIM2 Interrupt */
TIM3_IRQn = 16, /*!< TIM3 Interrupt */
TIM14_IRQn = 19, /*!< TIM14 Interrupt */
TIM16_IRQn = 21, /*!< TIM16 Interrupt */
TIM17_IRQn = 22, /*!< TIM17 Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Interrupt */
SPI1_IRQn = 25, /*!< SPI1 Interrupt */
SPI2_IRQn = 26, /*!< SPI2 Interrupt */
USART1_IRQn = 27, /*!< USART1 Interrupt */
USART2_IRQn = 28, /*!< USART2 Interrupt */
CEC_CAN_IRQn = 30, /*!< CEC and CAN Interrupts */
USB_IRQn = 31 /*!< USB Low Priority global Interrupt */
#elif defined (STM32F091)
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
PVD_VDDIO2_IRQn = 1, /*!< PVD & VDDIO2 Interrupts through EXTI Lines 16 and 31 */
RTC_IRQn = 2, /*!< RTC Interrupt through EXTI Lines 17, 19 and 20 */
FLASH_IRQn = 3, /*!< FLASH global Interrupt */
RCC_CRS_IRQn = 4, /*!< RCC & CRS Global Interrupts */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
TSC_IRQn = 8, /*!< Touch Sensing Controller Interrupts */
DMA1_Ch1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Ch2_3_DMA2_Ch1_2_IRQn = 10, /*!< DMA1 Channel 2 and 3 & DMA2 Channel 1 and 2 Interrupts */
DMA1_Ch4_7_DMA2_Ch3_5_IRQn = 11, /*!< DMA1 Channel 4 to 7 & DMA2 Channel 3 to 5 Interrupts */
ADC1_COMP_IRQn = 12, /*!< ADC, COMP1 and COMP2 Interrupts (EXTI Lines 21 and 22) */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM2_IRQn = 15, /*!< TIM2 global Interrupt */
TIM3_IRQn = 16, /*!< TIM3 global Interrupt */
TIM6_DAC_IRQn = 17, /*!< TIM6 global and DAC channel underrun error Interrupts */
TIM7_IRQn = 18, /*!< TIM7 global Interrupt */
TIM14_IRQn = 19, /*!< TIM14 global Interrupt */
TIM15_IRQn = 20, /*!< TIM15 global Interrupt */
TIM16_IRQn = 21, /*!< TIM16 global Interrupt */
TIM17_IRQn = 22, /*!< TIM17 global Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Event Interrupt & EXTI Line23 Interrupt (I2C1 wakeup) */
I2C2_IRQn = 24, /*!< I2C2 Event Interrupt & EXTI Line24 Interrupt (I2C2 wakeup) */
SPI1_IRQn = 25, /*!< SPI1 global Interrupt */
SPI2_IRQn = 26, /*!< SPI2 global Interrupt */
USART1_IRQn = 27, /*!< USART1 global Interrupt & EXTI Line25 Interrupt (USART1 wakeup) */
USART2_IRQn = 28, /*!< USART2 global Interrupt & EXTI Line26 Interrupt (USART2 wakeup) */
USART3_8_IRQn = 29, /*!< USART3 to USART8 global Interrupts */
CEC_CAN_IRQn = 30 /*!< CEC and CAN global Interrupts & EXTI Line27 Interrupt */
#elif defined (STM32F070xB)
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
RTC_IRQn = 2, /*!< RTC Interrupt through EXTI Lines 17, 19 and 20 */
FLASH_IRQn = 3, /*!< FLASH global Interrupt */
RCC_IRQn = 4, /*!< RCC Global Interrupts */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */
ADC1_IRQn = 12, /*!< ADC1 interrupts (ADC interrupt combined with EXTI Lines 21 and 22 */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM3_IRQn = 16, /*!< TIM3 global Interrupt */
TIM6_IRQn = 17, /*!< TIM6 global Interrupts */
TIM7_IRQn = 18, /*!< TIM7 global Interrupt */
TIM14_IRQn = 19, /*!< TIM14 global Interrupt */
TIM15_IRQn = 20, /*!< TIM15 global Interrupt */
TIM16_IRQn = 21, /*!< TIM16 global Interrupt */
TIM17_IRQn = 22, /*!< TIM17 global Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Event Interrupt & EXTI Line23 Interrupt (I2C1 wakeup) */
I2C2_IRQn = 24, /*!< I2C2 Event Interrupt */
SPI1_IRQn = 25, /*!< SPI1 global Interrupt */
SPI2_IRQn = 26, /*!< SPI2 global Interrupt */
USART1_IRQn = 27, /*!< USART1 global Interrupt */
USART2_IRQn = 28, /*!< USART2 global Interrupt */
USART3_4_IRQn = 29, /*!< USART3 and USART4 global Interrupts */
USB_IRQn = 31 /*!< USB global Interrupts & EXTI Line18 Interrupt */
#elif defined (STM32F070x6)
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
RTC_IRQn = 2, /*!< RTC Interrupt through EXTI Lines 17, 19 and 20 */
FLASH_IRQn = 3, /*!< FLASH global Interrupt */
RCC_IRQn = 4, /*!< RCC Global Interrupts */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */
ADC1_IRQn = 12, /*!< ADC1 Interrupt */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM3_IRQn = 16, /*!< TIM3 global Interrupt */
TIM14_IRQn = 19, /*!< TIM14 global Interrupt */
TIM16_IRQn = 21, /*!< TIM16 global Interrupt */
TIM17_IRQn = 22, /*!< TIM17 global Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Event Interrupt & EXTI Line23 Interrupt (I2C1 wakeup) */
SPI1_IRQn = 25, /*!< SPI1 global Interrupt */
USART1_IRQn = 27, /*!< USART1 global Interrupt & EXTI Line25 Interrupt (USART1 wakeup) */
USART2_IRQn = 28, /*!< USART2 global Interrupt */
USB_IRQn = 31 /*!< USB global Interrupts & EXTI Line18 Interrupt */
#elif defined (STM32F030xC)
WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
RTC_IRQn = 2, /*!< RTC Interrupt through EXTI Lines 17, 19 and 20 */
FLASH_IRQn = 3, /*!< FLASH global Interrupt */
RCC_IRQn = 4, /*!< RCC Global Interrupts */
EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */
EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */
EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */
DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */
DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */
DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */
ADC1_IRQn = 12, /*!< ADC Interrupts */
TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */
TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */
TIM3_IRQn = 16, /*!< TIM3 global Interrupt */
TIM6_IRQn = 17, /*!< TIM6 global Interrupts */
TIM7_IRQn = 18, /*!< TIM7 global Interrupt */
TIM14_IRQn = 19, /*!< TIM14 global Interrupt */
TIM15_IRQn = 20, /*!< TIM15 global Interrupt */
TIM16_IRQn = 21, /*!< TIM16 global Interrupt */
TIM17_IRQn = 22, /*!< TIM17 global Interrupt */
I2C1_IRQn = 23, /*!< I2C1 Event Interrupt & EXTI Line23 Interrupt (I2C1 wakeup) */
I2C2_IRQn = 24, /*!< I2C2 Event Interrupt */
SPI1_IRQn = 25, /*!< SPI1 global Interrupt */
SPI2_IRQn = 26, /*!< SPI2 global Interrupt */
USART1_IRQn = 27, /*!< USART1 global Interrupt & EXTI Line25 Interrupt (USART1 wakeup) */
USART2_IRQn = 28, /*!< USART2 global Interrupt & EXTI Line26 Interrupt (USART2 wakeup) */
USART3_6_IRQn = 29, /*!< USART3 to USART6 global Interrupts */
#endif /* STM32F051 */
}IRQn_Type;
/**
* @}
*/
#include "core_cm0.h"
#include "system_stm32f0xx.h"
#include
/** @addtogroup Exported_types
* @{
*/
typedef enum {RESET = 0, SET = !RESET} FlagStatus, ITStatus;
typedef enum {DISABLE = 0, ENABLE = !DISABLE} FunctionalState;
#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE))
typedef enum {ERROR = 0, SUCCESS = !ERROR} ErrorStatus;
/** @addtogroup Peripheral_registers_structures
* @{
*/
/**
* @brief Analog to Digital Converter
*/
typedef struct
{
__IO uint32_t ISR; /*!< ADC Interrupt and Status register, Address offset:0x00 */
__IO uint32_t IER; /*!< ADC Interrupt Enable register, Address offset:0x04 */
__IO uint32_t CR; /*!< ADC Control register, Address offset:0x08 */
__IO uint32_t CFGR1; /*!< ADC Configuration register 1, Address offset:0x0C */
__IO uint32_t CFGR2; /*!< ADC Configuration register 2, Address offset:0x10 */
__IO uint32_t SMPR; /*!< ADC Sampling time register, Address offset:0x14 */
uint32_t RESERVED1; /*!< Reserved, 0x18 */
uint32_t RESERVED2; /*!< Reserved, 0x1C */
__IO uint32_t TR; /*!< ADC watchdog threshold register, Address offset:0x20 */
uint32_t RESERVED3; /*!< Reserved, 0x24 */
__IO uint32_t CHSELR; /*!< ADC channel selection register, Address offset:0x28 */
uint32_t RESERVED4[5]; /*!< Reserved, 0x2C */
__IO uint32_t DR; /*!< ADC data register, Address offset:0x40 */
} ADC_TypeDef;
typedef struct
{
__IO uint32_t CCR;
} ADC_Common_TypeDef;
/**
* @brief Controller Area Network TxMailBox
*/
typedef struct
{
__IO uint32_t TIR; /*!< CAN TX mailbox identifier register */
__IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */
__IO uint32_t TDLR; /*!< CAN mailbox data low register */
__IO uint32_t TDHR; /*!< CAN mailbox data high register */
} CAN_TxMailBox_TypeDef;
/**
* @brief Controller Area Network FIFOMailBox
*/
typedef struct
{
__IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */
__IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */
__IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */
__IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */
} CAN_FIFOMailBox_TypeDef;
/**
* @brief Controller Area Network FilterRegister
*/
typedef struct
{
__IO uint32_t FR1; /*!< CAN Filter bank register 1 */
__IO uint32_t FR2; /*!< CAN Filter bank register 1 */
} CAN_FilterRegister_TypeDef;
/**
* @brief Controller Area Network
*/
typedef struct
{
__IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */
__IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */
__IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */
__IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */
__IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */
__IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */
__IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */
__IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */
uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */
CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */
CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */
uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */
__IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */
__IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */
uint32_t RESERVED2; /*!< Reserved, 0x208 */
__IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */
uint32_t RESERVED3; /*!< Reserved, 0x210 */
__IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */
uint32_t RESERVED4; /*!< Reserved, 0x218 */
__IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */
uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */
CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */
} CAN_TypeDef;
/**
* @brief HDMI-CEC
*/
typedef struct
{
__IO uint32_t CR; /*!< CEC control register, Address offset:0x00 */
__IO uint32_t CFGR; /*!< CEC configuration register, Address offset:0x04 */
__IO uint32_t TXDR; /*!< CEC Tx data register , Address offset:0x08 */
__IO uint32_t RXDR; /*!< CEC Rx Data Register, Address offset:0x0C */
__IO uint32_t ISR; /*!< CEC Interrupt and Status Register, Address offset:0x10 */
__IO uint32_t IER; /*!< CEC interrupt enable register, Address offset:0x14 */
}CEC_TypeDef;
/**
* @brief Comparator
*/
typedef struct
{
__IO uint32_t CSR; /*!< COMP comparator control and status register, Address offset: 0x1C */
} COMP_TypeDef;
/**
* @brief CRC calculation unit
*/
typedef struct
{
__IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */
__IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */
uint8_t RESERVED0; /*!< Reserved, 0x05 */
uint16_t RESERVED1; /*!< Reserved, 0x06 */
__IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */
uint32_t RESERVED2; /*!< Reserved, 0x0C */
__IO uint32_t INIT; /*!< Initial CRC value register, Address offset: 0x10 */
__IO uint32_t POL; /*!< CRC polynomial register, Address offset: 0x14 */
} CRC_TypeDef;
/**
* @brief Clock Recovery System
*/
typedef struct
{
__IO uint32_t CR; /*!< CRS ccontrol register, Address offset: 0x00 */
__IO uint32_t CFGR; /*!< CRS configuration register, Address offset: 0x04 */
__IO uint32_t ISR; /*!< CRS interrupt and status register, Address offset: 0x08 */
__IO uint32_t ICR; /*!< CRS interrupt flag clear register, Address offset: 0x0C */
} CRS_TypeDef;
/**
* @brief Digital to Analog Converter
*/
typedef struct
{
__IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */
__IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */
__IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */
__IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */
__IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */
__IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */
__IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */
__IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */
__IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */
__IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */
__IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */
__IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */
__IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */
__IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */
} DAC_TypeDef;
/**
* @brief Debug MCU
*/
typedef struct
{
__IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */
__IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */
__IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */
__IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */
}DBGMCU_TypeDef;
/**
* @brief DMA Controller
*/
typedef struct
{
__IO uint32_t CCR; /*!< DMA channel x configuration register */
__IO uint32_t CNDTR; /*!< DMA channel x number of data register */
__IO uint32_t CPAR; /*!< DMA channel x peripheral address register */
__IO uint32_t CMAR; /*!< DMA channel x memory address register */
} DMA_Channel_TypeDef;
typedef struct
{
__IO uint32_t ISR; /*!< DMA interrupt status register, Address offset: 0x00 */
__IO uint32_t IFCR; /*!< DMA interrupt flag clear register, Address offset: 0x04 */
uint32_t RESERVED0[40];/*!< Reserved as declared by channel typedef 0x08 - 0xA4*/
__IO uint32_t RMPCR; /*!< Remap control register, Address offset: 0xA8 */
}DMA_TypeDef;
/**
* @brief External Interrupt/Event Controller
*/
typedef struct
{
__IO uint32_t IMR; /*! exti[31] Interrupt */
#define SYSCFG_ITLINE1_SR_VDDIO2 ((uint32_t)0x00000002) /*!< VDDIO2 -> exti[16] Interrupt */
#define SYSCFG_ITLINE2_SR_RTC_WAKEUP ((uint32_t)0x00000001) /*!< RTC WAKEUP -> exti[20] Interrupt */
#define SYSCFG_ITLINE2_SR_RTC_TSTAMP ((uint32_t)0x00000002) /*!< RTC Time Stamp -> exti[19] interrupt */
#define SYSCFG_ITLINE2_SR_RTC_ALRA ((uint32_t)0x00000003) /*!< RTC Alarm -> exti[17] interrupt .... */
#define SYSCFG_ITLINE3_SR_FLASH_ITF ((uint32_t)0x00000001) /*!< Flash ITF Interrupt */
#define SYSCFG_ITLINE4_SR_CRS ((uint32_t)0x00000001) /*!< CRS interrupt */
#define SYSCFG_ITLINE4_SR_CLK_CTRL ((uint32_t)0x00000002) /*!< CLK CTRL interrupt */
#define SYSCFG_ITLINE5_SR_EXTI0 ((uint32_t)0x00000001) /*!< External Interrupt 0 */
#define SYSCFG_ITLINE5_SR_EXTI1 ((uint32_t)0x00000002) /*!< External Interrupt 1 */
#define SYSCFG_ITLINE6_SR_EXTI2 ((uint32_t)0x00000001) /*!< External Interrupt 2 */
#define SYSCFG_ITLINE6_SR_EXTI3 ((uint32_t)0x00000002) /*!< External Interrupt 3 */
#define SYSCFG_ITLINE7_SR_EXTI4 ((uint32_t)0x00000001) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI5 ((uint32_t)0x00000002) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI6 ((uint32_t)0x00000004) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI7 ((uint32_t)0x00000008) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI8 ((uint32_t)0x00000010) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI9 ((uint32_t)0x00000020) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI10 ((uint32_t)0x00000040) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI11 ((uint32_t)0x00000080) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI12 ((uint32_t)0x00000100) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI13 ((uint32_t)0x00000200) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI14 ((uint32_t)0x00000400) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE7_SR_EXTI15 ((uint32_t)0x00000800) /*!< External Interrupt 15 to 4 */
#define SYSCFG_ITLINE8_SR_TSC_EOA ((uint32_t)0x00000001) /*!< Touch control EOA Interrupt */
#define SYSCFG_ITLINE8_SR_TSC_MCE ((uint32_t)0x00000002) /*!< Touch control MCE Interrupt */
#define SYSCFG_ITLINE9_SR_DMA1_CH1 ((uint32_t)0x00000001) /*!< DMA1 Channel 1 Interrupt */
#define SYSCFG_ITLINE10_SR_DMA1_CH2 ((uint32_t)0x00000001) /*!< DMA1 Channel 2 Interrupt */
#define SYSCFG_ITLINE10_SR_DMA1_CH3 ((uint32_t)0x00000002) /*!< DMA2 Channel 3 Interrupt */
#define SYSCFG_ITLINE10_SR_DMA2_CH1 ((uint32_t)0x00000004) /*!< DMA2 Channel 1 Interrupt */
#define SYSCFG_ITLINE10_SR_DMA2_CH2 ((uint32_t)0x00000008) /*!< DMA2 Channel 2 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA1_CH4 ((uint32_t)0x00000001) /*!< DMA1 Channel 4 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA1_CH5 ((uint32_t)0x00000002) /*!< DMA1 Channel 5 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA1_CH6 ((uint32_t)0x00000004) /*!< DMA1 Channel 6 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA1_CH7 ((uint32_t)0x00000008) /*!< DMA1 Channel 7 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA2_CH3 ((uint32_t)0x00000010) /*!< DMA2 Channel 3 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA2_CH4 ((uint32_t)0x00000020) /*!< DMA2 Channel 4 Interrupt */
#define SYSCFG_ITLINE11_SR_DMA2_CH5 ((uint32_t)0x00000040) /*!< DMA2 Channel 5 Interrupt */
#define SYSCFG_ITLINE12_SR_ADC ((uint32_t)0x00000001) /*!< ADC Interrupt */
#define SYSCFG_ITLINE12_SR_COMP1 ((uint32_t)0x00000002) /*!< COMP1 Interrupt -> exti[21] */
#define SYSCFG_ITLINE12_SR_COMP2 ((uint32_t)0x00000004) /*!< COMP2 Interrupt -> exti[22] */
#define SYSCFG_ITLINE13_SR_TIM1_BRK ((uint32_t)0x00000001) /*!< TIM1 BRK Interrupt */
#define SYSCFG_ITLINE13_SR_TIM1_UPD ((uint32_t)0x00000002) /*!< TIM1 UPD Interrupt */
#define SYSCFG_ITLINE13_SR_TIM1_TRG ((uint32_t)0x00000004) /*!< TIM1 TRG Interrupt */
#define SYSCFG_ITLINE13_SR_TIM1_CCU ((uint32_t)0x00000008) /*!< TIM1 CCU Interrupt */
#define SYSCFG_ITLINE14_SR_TIM1_CC ((uint32_t)0x00000001) /*!< TIM1 CC Interrupt */
#define SYSCFG_ITLINE15_SR_TIM2_GLB ((uint32_t)0x00000001) /*!< TIM2 GLB Interrupt */
#define SYSCFG_ITLINE16_SR_TIM3_GLB ((uint32_t)0x00000001) /*!< TIM3 GLB Interrupt */
#define SYSCFG_ITLINE17_SR_DAC ((uint32_t)0x00000001) /*!< DAC Interrupt */
#define SYSCFG_ITLINE17_SR_TIM6_GLB ((uint32_t)0x00000002) /*!< TIM6 GLB Interrupt */
#define SYSCFG_ITLINE18_SR_TIM7_GLB ((uint32_t)0x00000001) /*!< TIM7 GLB Interrupt */
#define SYSCFG_ITLINE19_SR_TIM14_GLB ((uint32_t)0x00000001) /*!< TIM14 GLB Interrupt */
#define SYSCFG_ITLINE20_SR_TIM15_GLB ((uint32_t)0x00000001) /*!< TIM15 GLB Interrupt */
#define SYSCFG_ITLINE21_SR_TIM16_GLB ((uint32_t)0x00000001) /*!< TIM16 GLB Interrupt */
#define SYSCFG_ITLINE22_SR_TIM17_GLB ((uint32_t)0x00000001) /*!< TIM17 GLB Interrupt */
#define SYSCFG_ITLINE23_SR_I2C1_GLB ((uint32_t)0x00000001) /*!< I2C1 GLB Interrupt -> exti[23] */
#define SYSCFG_ITLINE24_SR_I2C2_GLB ((uint32_t)0x00000001) /*!< I2C2 GLB Interrupt */
#define SYSCFG_ITLINE25_SR_SPI1 ((uint32_t)0x00000001) /*!< SPI1 Interrupt */
#define SYSCFG_ITLINE26_SR_SPI2 ((uint32_t)0x00000001) /*!< SPI2 Interrupt */
#define SYSCFG_ITLINE27_SR_USART1_GLB ((uint32_t)0x00000001) /*!< USART1 GLB Interrupt -> exti[25] */
#define SYSCFG_ITLINE28_SR_USART2_GLB ((uint32_t)0x00000001) /*!< USART2 GLB Interrupt -> exti[26] */
#define SYSCFG_ITLINE29_SR_USART3_GLB ((uint32_t)0x00000001) /*!< USART3 GLB Interrupt -> exti[28] */
#define SYSCFG_ITLINE29_SR_USART4_GLB ((uint32_t)0x00000002) /*!< USART4 GLB Interrupt */
#define SYSCFG_ITLINE29_SR_USART5_GLB ((uint32_t)0x00000004) /*!< USART5 GLB Interrupt */
#define SYSCFG_ITLINE29_SR_USART6_GLB ((uint32_t)0x00000008) /*!< USART6 GLB Interrupt */
#define SYSCFG_ITLINE29_SR_USART7_GLB ((uint32_t)0x00000010) /*!< USART7 GLB Interrupt */
#define SYSCFG_ITLINE29_SR_USART8_GLB ((uint32_t)0x00000020) /*!< USART8 GLB Interrupt */
#define SYSCFG_ITLINE30_SR_CAN ((uint32_t)0x00000001) /*!< CAN Interrupt */
#define SYSCFG_ITLINE30_SR_CEC ((uint32_t)0x00000002) /*!< CEC Interrupt */
/******************************************************************************/
/* */
/* Timers (TIM) */
/* */
/******************************************************************************/
/******************* Bit definition for TIM_CR1 register ********************/
#define TIM_CR1_CEN ((uint16_t)0x0001) /*!